收藏本站
W25Q16DW
7.2.36
Program Security Registers (42h)
The Program Security Register instruction is similar to the Page Program instruction. It allows from one
byte to 256 bytes of security register data to be programmed at previously erased (FFh) memory locations.
A Write Enable instruction must be executed before the device will accept the Program Security Register
Instruction (Status Register bit WEL= 1). The instruction is initiated by driving the /CS pin low then shifting
the instruction code “42h” followed by a 24-bit address (A23-A0) and at least one data byte, into the DI pin.
The /CS pin must be held low for the entire length of the instruction while data is being sent to the device.
ADDRESS
Security Register #0*
Security Register #1
Security Register #2
Security Register #3
A23-16
00h
00h
00h
00h
A15-12
0000
0001
0010
0011
A11-8
0000
0000
0000
0000
A7-0
Byte Address
Byte Address
Byte Address
Byte Address
* Please note that Security Register 0 is Reserved by Winbond for future use. It is
recommended to use Security registers 1- 3 before using register 0 .
The Program Security Register instruction sequence is shown in Figure 35. The Security Register Lock
Bits (LB3-0) in the Status Register-2 can be used to OTP protect the security registers. Once a lock bit is
set to 1, the corresponding security register will be permanently locked, Program Security Register
instruction to that register will be ignored (See 11.1.9, 11.2.21 for detail descriptions).
/CS
Mode 3
0
1
2
3
4
5
6
7
8
9
10
28
29
30
31
32
33
34
35
36
37
38
39
CLK
Mode 0
Instruction (42h)
24-Bit Address
Data Byte 1
DI
(IO 0 )
* = MSB
23
*
22
21
3
2
1
0
7
*
6
5
4
3
2
1
0
/CS
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Mode 3
CLK
Mode 0
Data Byte 2
Data Byte 3
Data Byte 256
DI
(IO 0 )
0
7
*
6
5
4
3
2
1
0
7
*
6
5
4
3
2
1
0
7
*
6
5
4
3
2
1
0
Figure 35. Program Security Registers Instruction (SPI Mode only)
- 62 -
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
W25Q16VSFIG IC FLASH 16MBIT 80MHZ 16SOIC
W25Q32BVZPIG IC SPI FLASH 32MBIT 8WSON
W25Q32DWZEIG IC FLASH SPI 32MBIT 8WSON
W25Q40BWSSIG IC FLASH SPI 4MBIT 8SOIC
W25Q40BWZPIG IC FLASH SPI 4MBIT 8WSON
W25Q64BVSFIG IC SPI FLASH 64MBIT 16SOIC
W25Q64CVZEIG IC SPI FLASH 64MBIT 8WSON
W25Q64DWZEIG IC FLASH SPI 64MBIT 8WSON
相关代理商/技术参数
W25Q16DWSFIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIG 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSNIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWSSIG 功能描述:IC FLASH SPI 16MBIT 8SOIC RoHS:是 类别:集成电路 (IC) >> 存储器 系列:SpiFlash® 标准包装:2,500 系列:- 格式 - 存储器:EEPROMs - 串行 存储器类型:EEPROM 存储容量:1K (128 x 8) 速度:100kHz 接口:UNI/O?（单线） 电源电压:1.8 V ~ 5.5 V 工作温度:-40°C ~ 85°C 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-MSOP 包装:带卷 (TR)
W25Q16DWSSIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16DWZPIG 制造商:Winbond Electronics Corp 功能描述:IC FLASH 16MBIT 104MHZ 8WSON
W25Q16DWZPIP 制造商:WINBOND 制造商全称:Winbond 功能描述:1.8V 16M-BIT SERIAL FLASH MEMORY WITH DUAL/QUAD SPI & QPI
W25Q16V 制造商:WINBOND 制造商全称:Winbond 功能描述:16M-BIT SERIAL FLASH MEMORY WITH DUAL AND QUAD SPI